eyc-ffm05-liquid-turbine-flow-transmitter-eyc-tech-viet-nam-stc-viet-nam.png

ĐẠI ĐIỆN EYC TECH TẠI VIỆT NAM

Công Ty TNHH TMDV Song Thành Công là Đại lý ủy quyền chính thức của hãng EYC TECH TẠI VIỆT NAM. Các sản phẩm tiêu biểu như Thiết bị đo lưu lượng, đo áp suất, độ ẩm, nhiệt độ, Hệ thống đo khí gas, CO, hệ thống đọc tín hiệu từ các thiết bị đo áp, nhiệt, lưu lượng, được dùng nhiều trong các ngành Năng lượng mặt trời, công nghiệp Điện gió, Điện tử, hàng hóa tiêu dùng, hệ thống HVAC, hệ thống xử lý nước, ngành sản xuất phi kim, nhà kính, thực phẩm và công nghệ sinh học, tòa nhà thông minh, tự động hóa...

eYc FFM05 Liquid Turbine Flow Transmitter được EYC TECH Việt Nam đang phân phối rộng rãi tại thị trường Việt Nam. eYc FFM05 được thiết kế theo tiêu chuẩn công nghiệp, dễ dàng kết nối với các hệ thống giám sát DCS, PLC, Mô đun I/O...Sản phẩm hiện đang được sử dụng để đo lường trong các lĩnh vực như: Dầu khí, Điện lực, Sân Bay, Năng Lượng mặt trời, quan trắc thời tiết, khí tượng thủy văn, giao thông-đô thị thông minh.

Tính năng chính:

Liquid flows through the turbine housing causing an internal rotor to spin. As the rotor spins, an electrical signal is generated in the pickup coil. This signal is converted into engineering units(Liters, cubic meters, gallons etc.)on the local display where is applicable. Optional accessory modules can be used to export the signal to other equipment.

EYC TECH VIETNAM - YUDEN TECH VIETNAM - ĐẠI ĐIỆN EYC TECH TẠI VIỆT NAM - STC VIETNAM ĐẠI DIỆN ĐỘC QUYỀN CHÍNH THỨC CỦA HÃNG

Thông số kỹ thuật:

Measured value:Flow rate, Volume flow
Medium:Liquid:Water;Diesel, etc.(without impurity, low viscosity, flow conditions similar to EN 29104)
Temperature:+10 ... +30°C / +50 ... +86°F
Output:Pulse, 4 … 20 mA(Option:Local display+4 ... 20 mA)
Accuracy:0.5% of rate(Optional:0.2%)
Diameter:DN4 … DN200
Measuring ratio:Standard-10:1;Optional-20:1
Inlet section:≥10 DN
Operating pressure:1 bar
Installation conditions:Inlet run≥10 DN;Outlet run≥5 DN(Take care that flow sensor is always fully filled)
Flow direction:Forward(Arrow on flow sensor indicates flow direction)
Connection

Thread:DN4 … DN50(External);DN15 … DN50(Internal)
Flange(Optional):ANSI / JIS
Operating conditions
Process temperature:-20 ... +80°C / -20 ... +150°C
Ambient temperature(All versions):Standard(with aluminum converter housing):20 … +55°C
Storage temperature:-20 ... +70°C
Pressure:Thread:63 bar(DN4 … DN15) / 25 bar(DN20 … DN50)
                  Flange:16 bar
                  ANSI:150 Ib RF
                  JIS:10K
Material
Housing:SS304(Optional:SS316)
Flanges:SS304
Rotor:2Cr13(Optional:Duplex impeller)
Bearings and shafts:Tungsten carbide
Display meter:Standard:Polyurethane coated die-cast aluminum